4 x DDR DIMM sockets   supporting up to 128 GB (32 GB single DIMM capacity) of system memory

Dual channel memory   architecture

Support for ECC   Un-buffered DIMM 1Rx8/2Rx8 memory modules (operate in non-ECC mode)

Support for non-ECC   Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules

Support for Extreme   Memory Profile (XMP) memory modules

(Please refer   “Memory Support List” for more information.)

1 x USB Type-C® port,   supporting USB Type-C® and DisplayPort video outputs and a maximum resolution   of 4096×[email protected] Hz

* Support for drawing tablets   and [email protected] of power delivery.

* Support for   DisplayPort 1.2 version and HDCP 2.3

1 x HDMI port,   supporting a maximum resolution of 4096×[email protected] Hz

* Support for HDMI 1.4   version and HDCP 2.3.

(Graphics   specifications may vary depending on CPU or graphics card support.)

High Definition Audio

2-channel analog output

Support for S/PDIF Out

7.1-channel digital   signals

* Actual output of   digital signals may vary depending on the playback content and software used,   and an external DAC is required.

WIFI a, b, g, n, ac,   ax, supporting 2.4/5 GHz Dual-Band

BLUETOOTH 5.2

Support for 11ax 160MHz   wireless standard and up to 2.4 Gbps data rate

* Actual data rate may   vary depending on environment and equipment.

* For optimum   performance, if only one PCI Express graphics card is to be installed, be   sure to install it in the PCIEX16 slot.

(The PCIEX16 slot   conforms to PCI Express 5.0 standard.)

2 x PCI Express x16   slots, running at x4 (PCIEX4_1, PCIEX4_2)

(The PCIEX4 slots   conform to PCI Express 3.0 standard.)

1 x M.2 connector   (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2 SSD support) (M2A_CPU)

Chipset:

2 x M.2 connectors   (Socket 3, M key, type 2260/2280/22110 PCIe 4.0 x4/x2 SSD support) (M2P_SB,   M2Q_SB)

1 x M.2 connector   (Socket 3, M key, type 2260/2280/22110 SATA and PCIe 4.0 x4/x2 SSD support)   (M2M_SB)

6 x SATA 6Gb/s   connectors

Support for RAID 0,   RAID 1, RAID 5, and RAID 10

* Refer to “2-7   Internal Connectors,” for the installation notices for the M.2 and SATA   connectors.

Intel® Optane™ Memory   Ready

* System acceleration   with Intel® Optane™ Memory can only be enabled on the M.2 connectors   supported by the Chipset.

2 x USB Type-C® ports,   with USB 3.2 Gen 2×2 support (1 port on the back panel, 1 port available   through the internal USB header)

1 x USB Type-C® port on   the back panel, with USB 3.2 Gen 1 support

2 x USB 3.2 Gen 2   Type-A ports (red) on the back panel

2 x USB 3.2 Gen 1 ports   available through the internal USB header

2 x USB 2.0/1.1 ports   on the back panel

Chipset+USB 3.2 Gen 1   Hub:

4 x USB 3.2 Gen 1 ports   on the back panel

Chipset+USB 2.0 Hub:

4 x USB 2.0/1.1 ports   available through the internal USB headers

1 x 8-pin ATX 12V power   connector

1 x 4-pin ATX 12V power   connector

1 x CPU fan header

1 x water cooling CPU   fan header

4 x system fan headers

2 x system fan/water   cooling pump headers

2 x addressable LED   strip headers

2 x RGB LED strip   headers

4 x M.2 Socket 3   connectors

6 x SATA 6Gb/s   connectors

1 x front panel header

1 x front panel audio   header

1 x USB Type-C® header,   with USB 3.2 Gen 2×2 support

1 x USB 3.2 Gen 1   header

2 x USB 2.0/1.1 headers

1 x noise detection   header

2 x Thunderbolt™ add-in   card connectors

1 x Trusted Platform   Module header (For the GC-TPM2.0 SPI/GC-TPM2.0 SPI 2.0 module only)

1 x serial port header

1 x Q-Flash Plus button

1 x reset button

1 x reset jumper

2 x temperature sensor   headers

1 x Clear CMOS jumper

2 x SMA antenna   connectors (2T2R)

4 x USB 3.2 Gen 1 ports

1 x DisplayPort In port

1 x HDMI port

2 x USB 3.2 Gen 2   Type-A ports (red)

1 x USB Type-C® port, with   USB 3.2 Gen 2×2 support

1 x USB Type-C® port,   with USB 3.2 Gen 1 support

1 x RJ-45 port

1 x optical S/PDIF Out   connector

2 x audio jacks

Temperature detection

Fan speed detection

Water cooling flow rate   detection

Fan fail warning

Fan speed control

* Whether the fan   (pump) speed control function is supported will depend on the fan (pump) you   install.

Noise detection

Use of licensed AMI   UEFI BIOS

PnP 1.0a, DMI 2.7, WfM   2.0, SM BIOS 2.7, ACPI 5.0

* Available   applications in APP Center may vary by motherboard model. Supported functions   of each application may also vary depending on motherboard specifications.

@BIOS

EasyTune

Fast Boot

Game Boost

ON/OFF Charge

RGB Fusion

Smart Backup

System Information   Viewer

Support for Q-Flash   Plus

Support for Q-Flash

Support for Xpress   Install

cFosSpeed

Support for Windows 10   64-bit